Power Quality Studies: Identifying and Resolving Hidden Electrical Issues

When you think about electrical problems, you probably picture a complete outage—a blackout. But what if the lights are on, yet your facility is plagued by mysterious issues like random computer resets, flickering lights, overheating transformers, and unexplained equipment failures? In these cases, the problem isn’t a lack of power, but rather the quality of the power being supplied.

Power quality is a measure of how well the voltage, frequency, and waveform of a power supply conform to ideal specifications. For decades, most equipment was robust enough to handle minor deviations. But today’s world runs on sensitive microprocessors and sophisticated electronics that are far less tolerant. Poor power quality is like trying to run a high-performance engine on contaminated fuel; it may run for a while, but it will perform poorly and eventually suffer serious damage.

A power quality study is a specialized diagnostic process that acts like a health check-up for your electrical system, identifying these hidden and often costly issues so they can be resolved.

What is “Good” vs. “Poor” Power Quality?

In an ideal world, the electricity supplied to your facility would be a perfect, smooth sine wave at a constant voltage and frequency. In reality, numerous factors can distort this ideal picture. Poor power quality manifests in several ways, and identifying the specific culprit is the key to finding a solution.

Common Power Quality Issues Explained

A power quality study aims to identify and quantify several key disturbances:

1. Voltage Sags and Swells

• Sags (or Dips): Short-term decreases in voltage, often caused by the startup of large motors or nearby faults on the utility grid. Sags are a leading cause of problems, causing computers and sensitive controls to reboot, processes to shut down, and relays to drop out.
• Swells: Short-term increases in voltage, typically caused by the shutdown of large loads or lightning strikes. Swells can stress and degrade electronic components, leading to premature failure.

Explore Elecwatts for electrical engineering services in UAE. 

2. Transients (or Spikes)

These are extremely fast and powerful increases in voltage, lasting only microseconds but reaching thousands of volts. Often caused by lightning or the switching of large electrical loads, transients can cause catastrophic and immediate damage to microprocessors, memory, and other sensitive electronics.

3. Harmonics: The Invisible Menace

This is one of the most pervasive and misunderstood power quality issues today. Harmonics are distortions to the fundamental sine wave, creating extra, unwanted frequencies that are multiples of the standard 50 or 60 Hz.

• Source: The primary culprits are “non-linear loads,” which are ubiquitous in modern facilities. These include computers, LED lighting, variable frequency drives (VFDs), EV chargers, and uninterruptible power supplies (UPS).
• Effects: Harmonic currents don’t do useful work; they only generate excess heat. They can cause dangerously high currents on neutral wires (which are typically not protected by breakers), overheat and destroy transformers, and cause nuisance tripping of circuit breakers.

4. Voltage Flicker and Imbalance

• Flicker: Rapid, repetitive variations in voltage that cause perceptible changes in lighting. It’s often caused by large, cyclical loads like welders or rock crushers.
• Imbalance: A condition in a three-phase system where the voltages are not equal. This can cause motors to run inefficiently, overheat, and fail prematurely.

The Power Quality Study Process

Identifying the root cause of these issues requires a systematic approach.

1. Installation of Monitors: An engineer installs specialized power quality analyzers at key points in the electrical system, such as the main service entrance and feeders supplying problematic loads.
2. Data Logging: These monitors are left in place for a period—typically a week or more—to capture a comprehensive picture of the system’s behavior under all operating conditions. They record any deviation from the ideal waveform, timestamping every event.
3. Data Analysis: The engineer then analyzes the captured data. The “signature” of the recorded disturbances points to the likely cause. For instance, a voltage sag that occurs every morning at 8:00 AM likely corresponds to a large motor starting up. High levels of the 5th and 7th harmonics often point to a concentration of VFDs.
4. Root Cause Identification and Recommendations: Based on the analysis, the engineer identifies the source of the problem and recommends a targeted solution. For complex issues, this may require sophisticated modeling as part of a broader Project Lead Engineering & Management UAE.

Frequently Asked Questions (FAQs)

1. My lights are flickering. Is this a power quality issue?

Yes, it is very likely a power quality issue known as voltage flicker. It can be caused by large loads starting and stopping within your facility or by issues on the utility grid. A study can determine the source.

2. What is Total Harmonic Distortion (THD)?

THD is a measurement that quantifies the total amount of harmonic distortion present in a waveform. High THD levels (typically above 5-8% for voltage) indicate a significant harmonics problem that can cause overheating and equipment malfunction.

3. Can my facility cause power quality problems for my neighbors?

Yes. If your facility has large non-linear loads that generate significant harmonic currents, those currents can sometimes travel back onto the utility grid and affect the power quality of nearby customers.

4. Are power quality issues the utility’s fault or caused by my own equipment?

It can be either. Issues like transients from lightning or voltage sags from grid faults originate from the utility. However, issues like harmonics are almost always generated by equipment within your own facility. A power quality study is the only way to be certain.

5. How are harmonic issues resolved?

Solutions depend on the severity. They can range from installing harmonic-mitigating transformers to adding specialized passive or active harmonic filters that “trap” or cancel out the damaging harmonic currents.

Conclusion

In an era defined by sensitive electronics and sophisticated automation, maintaining high power quality is no longer a luxury—it’s an operational necessity. Persistent, unexplained electrical problems can severely impact productivity, increase maintenance costs, and shorten the lifespan of critical assets. A professional power quality study moves beyond guesswork, providing the clear, actionable data needed to diagnose and resolve these invisible issues.

By partnering with experts like Elecwatts GCC, facilities can implement targeted solutions that clean up their power, protecting their investments and ensuring a more reliable and efficient electrical system.