How to install a shower drain in a preformed base

How to install a shower drain in a preformed base
Read Time:3 Minute, 50 Second

To install a shower drain in a preformed base, you’ll need to drill the hole for the drain. You can then install the drainage pipe. This drain has a compression nut that screws into the base and a soft rubber compression gasket that fits around the opening. Then, you’ll need to tighten the nut from the inside of the drain. Once you’ve loosened the nut, you’ll need to install the grate over the opening.

Place your new shower base over the drainpipe, and mark it where the flange meets the bottom of the lower body.

You’ll need to place your new shower base over the drain pipe and mark it where the flange meets the bottom of the lower body. Then, cut the pipe to fit. Make sure to leave a 2-inch gap between the base and the pipe. Then, push the compression gasket into the drain pipe and the drain body. Push down on the compression gasket until it sets.

Once the joist is set, you can remove the old drain and start installing the new one. 

Once the joist is set, you can remove the old drain and start installing the new one. To do this, you must find a suitable location for the shower drain. The most common location is along the joist. It is because it’s more stable. If you need to patch the walls later, you can always use the stud as support. Afterward, it would be best to use a rubber gasket to seal the drain.

Remove the existing drain and remove the gasket. Ensure the floor is level before fitting the drain body over it. 

The next step is to install the new shower drain. To do this, you must remove the existing drain and the gasket. Ensure the floor is level before fitting the drain body over it. If you’re not careful, this can become a significant project. It’s essential to follow all instructions carefully and correctly, or the process will turn into a nightmare. So, take your time and don’t cut the walls unless you have all of the information you need to get the job done.

After the drain has been removed, you’ll need to install the new shower base. You’ll need to install the waterproof membrane and the drainpipe to do this. Nail the waterproof membrane to the joists. You’ll also need to nail up the new drain body to the studs. In the meantime, you can patch the wall with the tile. Check https://ipsplumbingproducts.com/wp-content/uploads/2020/12/Install_ABA_Brass-No-Caulk-Shower-Drain.pdf to ensure that you can do it well and can be guided by the experts.

 It should be wide enough to fit the pliers and screw them into place.

First, you need to make a hole in the floor for the drainpipe. It should be wide enough to fit the pliers and screw them into place. After installing the drain pipe, you need to install the pipe to the lower drain body. Glue the drain into the base. If the plastic drainpipe is in the bottom, it should be secured with a clamping ring. You’ll need a strong adhesive to keep the joist in place for the drain.

After removing the old shower base, you need to make a hole for the drain. 

The hole for the drain should be wide enough to fit the pliers and wider than the drain itself. You can then adjust the pliers according to the manufacturer’s recommendations. You can then attach the metal grate to the top of the drain. If you have the right tools, you can easily complete the installation.

Measure the center of the existing drain line. 

Measuring helps you avoid drilling holes where you didn’t need to drill. Remember to cut the old P-trap first to make it easy to connect the new drain. You’ll need to measure it before you start the work. You can use your measurements to mark the center of the old drain. Using your measuring tape, you can draw a line where the old drain should be.

Make sure that you’re not cutting the joists too close to the drain

Remove the old shower base. After removing the old shower base, you must mark the new one’s smooth socket with a pencil or a sharpie. You’ll need to draw a hole where the new P-trap will be inserted. Then, make sure that you’re not cutting the joists too close to the drain. After making the necessary cuts, you’ll need to cut the subfloor to the new hole.

Avatar

About Post Author

Happy
Happy
0
Sad
Sad
0
Excited
Excited
0
Sleepy
Sleepy
0
Angry
Angry
0
Surprise
Surprise
0